Design for FDM: walls, overhangs, holes and tolerances
Most problems with FDM parts are decided in CAD, not on the printer. A wall that is slightly thinner than two extrusion widths, a hole sized to the nominal shaft diameter, or a clip printed in the wrong orientation will cause trouble no matter how well the machine is tuned. Good design for FDM 3D printing is about working with how the process builds parts: layer by layer, from a nozzle of fixed width, with each layer resting on the one below.
The guidance below is general and works for most FDM materials. Exact values vary with material, layer height and geometry, so for any fit that matters, print a small test coupon first. It costs far less than reprinting a full assembly.
Wall thickness and nozzle width
FDM walls are built from extrusion lines, typically around 0.4 mm wide with a standard nozzle. A wall that is a clean multiple of that width prints solid and predictable. A wall that falls between multiples may leave a gap or a thin, weak infill line in the middle.
- Minimum practical wall: around two extrusion widths (roughly 0.8 mm) for non-structural features.
- Functional walls: 1.2-2 mm or more for enclosures, brackets and anything that takes load or screws.
- Consistency: keep wall thickness fairly uniform. Abrupt changes from thin to very thick sections can warp or show sink marks on the surface.
Overhangs, bridges and supports
Each layer needs something underneath it. Overhangs up to roughly 45 degrees from vertical usually print without support, because each layer overlaps the one below enough to stay up. Beyond that, the underside starts to droop and you will need support material or a design change.
Bridges, where a layer spans horizontally between two supports, are a special case. Short bridges of a few millimetres to a couple of centimetres usually print cleanly; longer spans start to sag. Supports are optional in our instant quote, but they leave marks on the surfaces they touch. Where you can, design them out:
- Replace flat overhangs with 45 degree chamfers underneath.
- Turn horizontal holes into a teardrop or diamond shape at the top so they self-support.
- Split the part so each piece has a flat face to sit on the bed.
- Orient cosmetic faces upwards or vertical, away from support contact.
Holes, clearances and fits
Printed holes usually come out slightly undersized, especially small vertical holes, because of how the nozzle traces curves. Horizontal holes can also lose roundness at the top. Treat the following as starting ranges, not guarantees:
| Fit type | Starting clearance | Notes |
|---|---|---|
| Press fit | 0-0.1 mm | Very sensitive to material and orientation. Test before committing. |
| Snug / location fit | 0.1-0.2 mm | Pins, dowels and parts that should not rattle. |
| Sliding / free fit | 0.2-0.4 mm | Moving parts, lids, hinges and assemblies printed separately. |
| Print-in-place clearance | 0.3-0.5 mm or more | Parts printed already assembled need larger gaps to avoid fusing. |
Orientation, anisotropy and where strength comes from
FDM parts are anisotropic: they are strongest along the extrusion lines within a layer and weakest between layers. A hook or clip printed standing upright, with layers stacked along its length, can split along a layer line under a load that the same part printed lying flat would easily take. Decide the print orientation while you design, and tell us if a particular face or direction is load-critical.
For strength, walls usually matter more than infill. Most bending and torsion stress is carried near the surface, so adding perimeters (wall lines) and top and bottom layers often helps more than raising infill. Infill in the instant quote ranges from 5% to 100%. Low infill suits display models and light fixtures; medium infill with extra walls is a sensible default for functional parts; high or full infill is worth it for small, heavily loaded parts or areas around inserts.
Fillets and chamfers
Sharp internal corners concentrate stress and are a common failure point. Add fillets where walls meet bosses, ribs and bases. On faces that sit on the build plate, a small chamfer works better than a fillet, because a fillet on the bottom edge creates a steep overhang. Chamfers also help counter slight "elephant foot" spread on the first layer.
Text and small features
Embossed or engraved text reads best when strokes are at least about 0.5 mm wide and depth is 0.5-1 mm. Text on vertical faces generally prints more crisply than on top surfaces. Very thin pins and posts (under about 2 mm diameter) are fragile and can wobble during printing; thicken them or replace them with a metal pin. For fine details, a smaller layer height helps; the instant quote lets you choose from 0.05 mm to 0.56 mm, with finer layers taking longer to print.
Large parts, threads and inserts
Our maximum build volume is 256 x 256 x 256 mm. Larger parts can be split into pieces and joined. When splitting, place the joint away from high-stress areas and add alignment features such as dowel pins, tongue-and-groove edges or dovetails. Plan for adhesive or screws at the joint, and keep each piece oriented so its strongest direction matches the load.
Printed threads work for coarse sizes and low cycle counts, but small metric threads (below about M6) are usually unreliable. For anything that will be assembled repeatedly, use heat-set brass inserts. Model the hole to the insert manufacturer's recommended diameter, give it at least a few wall lines of surrounding material, and leave a little depth below the insert for displaced plastic. Self-tapping screws into a correctly sized pilot hole are a simpler option for low-cycle joints.
Exporting a clean STL
A good STL avoids surprises in quoting and printing. Check these export settings in your CAD tool:
- Units in millimetres. A part exported in inches or metres arrives at the wrong scale. Check the bounding box after export.
- Sensible resolution. Curved faces should look smooth, not faceted. Use a fine chordal tolerance, but avoid extreme settings that create huge files with no visible benefit.
- Watertight mesh. The model must be a closed solid with no holes, flipped normals or internal faces. Most CAD tools and free mesh repair tools can check this.
- One file per part. Export each distinct part as its own STL so it can be quoted, oriented and counted correctly.
Pre-upload checklist and next steps
- Walls are at least about 0.8 mm, and 1.2 mm or more on functional areas.
- Overhangs beyond about 45 degrees are chamfered, redesigned or accepted with supports.
- Holes and mating parts have clearances chosen for the fit, and critical fits have been tested on a coupon.
- Print orientation suits the load direction, and you have noted any load-critical faces.
- Internal corners are filleted; bottom edges use chamfers.
- Text and small features are large enough to print cleanly.
- Parts larger than 256 x 256 x 256 mm are split with alignment features.
- Threads that will be reused have heat-set inserts.
- Each STL is in millimetres, watertight and exported separately.
Once the checklist is clear, upload your files for an instant quote and choose the material, layer height and infill. If you want a second opinion, tick Need help deciding? and the team will review the files before printing. Our materials comparison helps with material choice. For iterative development work, see prototyping services, and for batch runs or NDA projects, visit the business page.
Frequently asked questions
What is the minimum wall thickness for FDM printing?
As a general guide, about two extrusion widths, roughly 0.8 mm with a standard nozzle, for non-structural features. Functional walls are better at 1.2 mm or more.
What clearance should I use for parts that fit together?
Common starting points are 0.1-0.2 mm per side for snug fits and 0.2-0.4 mm for sliding fits. Results vary with material and orientation, so print a test coupon for critical fits.
Does higher infill make a part stronger?
It helps, but adding walls and top and bottom layers usually improves strength more efficiently, because most stress is carried near the surface. Print orientation also has a large effect.
What if my part is bigger than the build volume?
The maximum build volume is 256 x 256 x 256 mm. Larger parts can be split into pieces with alignment features and joined after printing.
Have parts to print?
Upload an STL for an instant price, or talk to us about batch runs and NDA projects.
Business enquiries